Pull down the moon dating Freesexywebcams

The three weights provide power to the hour strike (left weight), time (center weight), and chime melody (right weight).

Without these weights, the Grandfather Clock would not operate.

Copyright 2018 The Clock Depot Visit our Grandfather Clock Store - The Clock Depot - 3400 Westgate Dr - B11, Durham, NC 27707 Call us toll free at 1-866-402-8714 - Retail Store Hours Mon-Fri - EST - Call for Saturday hours Clocks at the lowest price allowed and free shipping on most selections The Clock Depot is a factory authorized Howard Miller distributor for all Howard Miller clocks and grandfather clocks.

We also cannot properly answer questions on older clocks, clocks that we have not sold or brands we do not sell.

Raising chain driven weights is accomplished by pulling down on the loose end of the chain.

The strike and chime sounds are made by a series of hammers hitting various length rods.

Using pliers, grip the bushing firmly by its sides so that it cannot slip in the pliers. Re-attach the hand to the shaft and turn the hand nut finger tight. If necessary, adjust hammers so that they do not interfere with each other while moving or striking the chime rods. Chime volume cannot be adjusted on a chime rod movement.

The minute hand has a small raised area on the back side directly around the shaft hole, this is the hand bushing. CHIME ROD hammer arms are made of brass and can be safely bent.

pull down the moon dating-18pull down the moon dating-15

Weights are hung from the movement by a cable or chain. The pendulum provides the ability to regulate and adjust the time keeping. As described within these instructions, adjustments to the pendulum to achieve accurate time keeping is easily accomplished. The movement controls the hour strike, time keeping, and chime. The pendulum and weights are critical components to operation of the Grandfather Clock movement. 15 Grandfather Clock Does Not Chime At Proper Time . The pendulum disk is moved up or down by turning the adjustment nut. To correct this rotate the minute hand backwards three hours as describe in Step 5 of the setup operation. Grip the bushing by its sides and turn the hand forward 5 minutes. (Reference: See AUTOMATIC NIGHTTIME SHUT OFF OPTION in General Information Section). Check hammer adjustment and correct chime tone as necessary. Move the chime selection lever to a different melody or to “silent”. It is possible that the styrofoam blocks located above the cable pulleys are binding the cable. Chime tone may be affected by the hammers resting on the chime rods or striking the rods off center. Changing the speed of time keeping is accomplished by moving the pendulum disk up or down. If the moon dial still cannot be easily advanced, this indicates that the gears that automatically advance the moon dial are engaged. Make sure that the selection lever is not in the “silent” position or halfway between two chime melody positions? Make sure that all the packing material is removed from the movement area. Make sure that the weights are hanging in the correct location Check the label on the bottom of each weight to ensure proper location. For models with nighttime silencing, make sure that the Grandfather Clock is not in the nighttime silence mode. DO NOT ADJUST CHIME HAMMERS, unless the chime tone is incorrect. If the hand does not point to the correct mark, repeat steps 2 and 3. We cannot be responsible for any user adjustments performed on any clocks outside of the clocks that we have sold. With your other hand, turn the Grandfather Clock hand forward or backward the distance necessary to chime at the correct time. Make sure the hand points to the correct location that you recorded in Step 1 plus any corrections you made in step 3. This is accomplished by bending the hammer arms slightly in the middle so that each hammer rests approximately 1/8” from each rod. This information is only for the clocks that we offer at this time and may or may not be appropriate for other brands and older clocks. In order to remove the panel, reach in through the front door and turn the plastic clip or remove the tape. Grasp the wood slats or knob with the tips of your fingers. The weights must be raised every seven (7) days or the Grandfather Clock will stop. As you face the Grandfather Clock, remove the top side panel, open the side door, or remove the back access panel. If after several hours of operation your Grandfather Clock does not strike the correct hour, grasp the HOUR HAND ONLY and move it forward or backward to line up with the correct hour on the dial indicated by the number of times the hour strikes. The panels may be held in place during shipment by tape or a plastic clip. When installing wooden or glass top side panels reverse steps 1 thru 5. DO NOT attempt to move the chime selection lever while the Grandfather Clock is chiming. See figure 18 for when it is safe to move the chime selection lever without damaging the movement.

Leave a Reply

Your email address will not be published. Required fields are marked *

One thought on “pull down the moon dating”